Seasoft Pro/C3 3mm Dry-Suit Hood for Full Face Mask (FFM)

SKU: SSTC3H

This item is no longer available.

Here are Similar Hoods:

Overview
Compare
Specs
Protection
Q&A

Questions & Answers

Stephen S : If my head from forehead straight around circumference (widest part) is 23 -1/2 inch and my neck is a 17 inch, which size should I buy? or should I measure from tip of the nose to tip of the nose?Mario C : Thank you for your question. since your measurements fall into two different sizes from the size chart, I would go for the larger one, in your case is the 2X in order to accommodate 17'' neck circumference. This hood like most will not cover your nose so you can disregard the nose to nose measurements.
Tom T : What are the meausurements for sizing?ANTONY M : Leisure Pro does have a good customer service department and will probably do exchanges without a problem order based on your hat size and if it is too small or too large exchange it .JUNE H : Size chart can be found here: <a href="http://www.leisurepro.com/api/getSizeChart?productId=SSTC3H" target="_blank">http://www.leisurepro.com/api/getSizeChart?productId=SSTC3H</a>JOSEPH E : I am not sure of the exact measurements. I am an average size adult male subject and I ordered a large. It is a little bit loose but not a problem. It would appear the sizes may run slightly larger than typical. However at the time I placed my order, there were no medium sizes available.
Shopper : Why Did You Choose This?SAM C : purchased to use with either a dry suit or wetsuit to create a good seal with a full face mask and to keep my hair out of my face!

Reviews about this item

Review Summary

2018-10-16T03:38:57

Rated 5 out of 5

A great Hood

I work my hood every day of the week except the weekends which this hood is put to the true test. This is my third one and I will buy another when it wares out.

JOHN B.

Seasoft Pro/C3 3mm Dry-Suit Hood for Full Face Mask (FFM) Specifications

  • Material

    Nylon-2 Neoprene Rubber

  • Thickness

    3mm

  • Seams

    Glued & Sewn

  • Closure

    None Pull-Over

  • UPC Code

    654367663820

SeaSoft Hoods M-2XL Size Chart
  Medium Large X-Large 2X-Large
Circumference of head at widest point (inches)
22-23 23-24 24-25 25-26
Circumference of head at widest point (cm)
56-58 58-61 61-63.5 63.5-66
Circumference of neck (inches) 14 15 16 17
Circumference of neck (cm) 35.5 38 40.5 43

About Seasoft Pro/C3 3mm Dry-Suit Hood for Full Face Mask (FFM)

FEATURED REVIEWS

A great Hood

By JOHN B.

I work my hood every day of the week except the weekends which this hood is put to the true test. This is my third one and I will buy another when it wares out.

When diving, the deeper a diver goes the colder it generally gets and with increasing pressure, a typical neoprene hood gets thinner. If the temperature is getting colder and your hood is getting thinner, you're going to get cold. And, when you consider that 35% of heat loss is from the head area, it seems like this would be a place to make sure you are adequately protected to ensure warmth and comfort.

The Seasoft Titanium PRO/C3 Hood has 4-different types of nylon-2 neoprene including compressed neoprene for the back-3 panels of the hood. This means that no matter how deep you go, they are still their original thickness and working to keep you warm!You will not find any seams down the middle of the chin either. This seam, found in almost all hoods today, can cause jaw fatigue. The Seam is there because it is less expensive to make a hood from just two halves. SeaSoft does not believe that a hood is the place to go cheap.

The hood has titanium flakes foil technology that creates 2-layers of titanium Foil that reflects cold away and reflects your heat in keeping you warmer than hoods without this technology. The 3mm material is going to naturally fit and stretch around your head better. This leaves less room for cold water to occupy under your hood, this helps to maintain warmth as well. There are also two very small holes for air to escape from the inside crown of the hood in case air enters your hood with a thin baffle built over the holes to prevent water from entering.

The Seasoft PRO / C3 3mm Dry Suit Hood is a commercial dry suit hood designed to be worn with a full-face mask in cold water. The PRO/C3 has a layer of skin-in neoprene on the inside and on the outside with a layer of tough nylonin between these two layers. The skin-in neoprene allows the hood to seal to your face and the full-face mask to Seal to the Hood.SeaSoft Pro/C3 Wetsuit Hood use 3mm neoprene with glued and sewn seams for strength and durability. The hood is available in multiple sizes and is black in color.

Seasoft Pro/C3 3mm Dry-Suit Hood for Full Face Mask (FFM) Features

  • Pro/C3 3mm Dry Suit Hood for Full Face Mask (FFM):
  • Specifically Designed for Full Face Mask Divers In-Cold-Water
  • 35% of Heat Loss from Head
  • Construction: 4 Different Types of Nylon-2 Neoprene
  • Compressed Neoprene:
    Back 3-Panels of Hood
    Won't Get Thinner at Depth
  • Thicker Neoprene: Warmer Dive
  • No Chin Seam: Reduced Jaw Fatigue
  • Titanium Flakes Foil Technology:
    2-Layers of Titanium Foil
    Reflects Cold Away & Reflects Your Body Heat In
  • 3mm Naturally Fit & Stretch Around Head Better
  • Small-Holes w/Thin-Baffle On-Inside-Crown Vent Trapped Air
  • Seams Glued & Sewn for Strength & Durability
  • Layer of Skin-In Neoprene On-Inside & Outside w/Layer of Tough Nylon In-Between
  • Skin-In Neoprene Allows Hood to Seal to Face & Full-Face Mask to Seal to Hood
  • Available in Multiple Sizes
  • Color: Black

Warranty Information

This product has a limited warranty of 24 months.

Key Features

  • Designed for Full Face Mask Divers
  • 3mm Compressed Neoprene Construction
  • No Chin Seam: Reduced Jaw Fatigue
  • Titanium Flakes Foil Technology
  • Vented for Releasing Trapped Air

What's in the box:

  • Pro/C3 3mm Dry-Suit Hood
  • Seasoft 2 Year Limited Warranty