XS Scuba Altair Octo RG300YL 035251

Mfg Part #: RG300YL
 $99.95 

Customer Reviews for XS Scuba Altair Octo:

See the top 20 most helpful scuba gear reviews

Average Customer Review: based on 2 reviews.

Rating: Very Nice
Reviewer: Jennifer Williams  -  View all my reviews
Fits perfectly into the clip I already had on my BC, works like it should.

Did this Review help?
No
Yes

420 out of 810 people found this review helpful.

Rating: Quick disconnect
Reviewer: James Carmin  -  View all my reviews
The Quick disconnect feature is nice to have also keeps the octo out of the way

Did this Review help?
No
Yes

370 out of 782 people found this review helpful.

Questions and Answers for XS Scuba Altair Octo:


  • Shane:

    Will this work with Atomic regulators B2 or ST1?

    Bob  (Certified Scuba Instructor at Scuba.com):

    Yes.

  • Luis:

    that is the size of the thread is on the hose? will it fit on a oceanic fdx10 regulator?

    Darrick  (Certified Scuba Instructor at Scuba.com):

    Hello Luis, yes this will fit into the low pressure port on your 1st stage. There is a set standard that all manufacture go by now a days. So all manufacture will work with other manufacture. the LP port is 3/8, and the HP port is 7/16.

RG300 - AltAir Octo

An Innovative Product Designed For Out-Of-Air Emergencies

So where is your octopus during the dive? Is it trailing along in the water behind you? Can you find it in an emergency? Can you find it at all?

XS Scuba has addressed that problem by developing the AltAir. The AltAir utilizes the same patented quick-release buckles used on today's most modern weight integrated BC's.

Snap the AltAir in place to the BC and forget about it. If you need it, then it will be there...everytime. Even after a giant stride from a 20' tuna tower...it's still there.

Yet, just grab and pull the AltAir, that's all that is needed to release the patented X-Lock buckle.

Limited Lifetime Warranty: Se owner's manual for details

Features:

Exclusive X-Lock attachment
Intelligent, inline mouthpiece orientation
Reliable, free flow resistant design
Patent #6,487,761
36' yellow hose

Regulators
It is important to provide the proper preventative maintenance in order to ensure the maximum performance and life of your regulator. The following procedures should be performed routinely after each use to ensure that the regulator is cleaned, inspected and prepared for the next use or for storage.
1. When the regulator is removed from the SCUBA cylinder valve, it is important that the dust cap or protector cap is installed over the first stage regulator inlet fitting or threaded DIN connector. This is critical to prevent the entrance of moisture into the first-stage. This cap or protector is normally attached to the first stage regulator and may therefore be wet. Wipe or blow the cap or protector completely dry before securing it over the inlet fitting or threaded DIN connector.
2. As soon as possible after diving, the regulator should be rinsed thoroughly with clean fresh water while attached to a cylinder and pressurized with air.
3. Rinsing alone will not sufficiently clean the regulator properly. To clean the regulator as thoroughly as possible, it should be soaked in warm (not over 120º F) tap water.
a. The preferred method is to attach the regulator to a charged SCUBA cylinder, open the cylinder valve to pressurize the regulator, and thoroughly soak both the first and second stages. Pressurizing the regulator will effectively prevent moisture or contamination from entering the regulator while it is soaking. While the regulator is soaking, depress the second stage purge button several times to agitate the water inside the second stage. This will help loosen any mineral deposits that may have adhered to internal components. You should also turn the adjustment knob (SeaAir only) several times to loosen any mineral deposits that may have settled around the shaft. Agitate the entire second stage regulator while submerged to allow the warm water to flow in and out of the housing, this will further loosen any mineral deposits and help flush them out. Also agitate the first stage regulator to ensure water has entered the ambientwater ports. If the regulator is equipped with an alternate air source, gauge console, and inflator hose, soak these and agitate as needed.
b. If soaking the regulator while pressurized is not feasible, it may be soaked unpressurized. Be sure the dust cap or DIN protector cap is secure over the first stage inlet or threaded connector. DO NOT depress the purge button or turn the adjustment knob or lever while regulator is submerged.
NOTE: When soaking or rinsing the SeaAir regulator unpressurized, check to ensure that the second-stage adjustment knob is turned completely 'in' (clockwise) to prevent moisture from entering the valve and LP hose.
CAUTION: DO NOT depress the purge button, loosen the first stage yoke screw, or turn the second stage adjustment knob all the way 'out' (SeaAir model) if the regulator is submerged unpressurized. Doing so will allow water to enter, and will require that the regulator be returned to an Authorized XS Scuba Dealer for service.
4. If regulator has been soaking in water, remove the regulator and cylinder from the water bath and wipe the regulator as dry as possible. Next, depressurize the regulator by turning the cylinder valve hand wheel off (clockwise). While looking at the submersible pressure gauge face, depress the purge button, continue to depress the purge button until the gauge reads zero and air flow can no longer be heard. Remove the regulator from the cylinder valve.
5. If the regulator is to be stored for a long period, it is good practice to wipe the hoses and rubber gauge boot with a light film of non-aerosol silicone grease, using a soft cloth.
6. The SeaAir regulator should be stored with the knob or lever turned all the way out. This will help extend the life of the low pressure seat.
7. When the regulator is completely dry, store it in a clean equipment box or sealed in a plastic bag. DO NOT store it where it may be exposed to excessive heat or near an electrical motor, which produces ozone. Prolonged exposure to extreme heat, ozone, chlorine, and ultraviolet rays can cause premature degradation of rubber parts and components.
8. Never store the regulator while it is still attached to a cylinder.
9. DO not use any type of solvent or petroleum based substances to clean or lubricate any part of the regulator. DO not expose any part of the regulator to aerosol sprays as some aerosol propellants attack or degrade rubber and plastic materials.
HAVE YOUR REGULATOR SERVICED AT LEAST ONCE A YEAR FROM AN AUTHORIZED XS SCUBA DEALER. YOUR PERSONAL SAFETY AND THE MECHANICAL INTEGRITY OF YOUR REGULATOR MAY DEPEND ON IT.
DO NOT attempt to perform any disassembly or service of your regulator. Doing so may cause the regulator to malfunction, and will render the XS Scuba warranty null and void. All service must be performed by an Authorized XS Scuba Dealer.

View all XS Scuba Octos/Spare Air

Choose Currency:

Scuba.com, 1752 Langley Avenue, Irvine CA 92614