BUY THIS...

Bare D6 Pro Drysuit 11134-EBL-S 066871

GET THIS FREE


Mfg Part #: 011116

Bare D6 Pro Drysuit

Options: 
 $1,369.95 
1 Questions
1 Answers
  • Brand new & completely redesigned 
    Not like most other sites that sell the old discontinued model
  • Free Backpack Bag Included
  • 6 MM high density compression-resistant neoprene
  • Easy rear shoulder entry - dry zipper across the back of the shoulders  
  • Outer layer laminated with Diamond Tuff Nylon for durability
  • No Stitch Technology for superior performance
  • Heavy duty latex wrist seals and 3mm neoprene neck seal
  • 360 degree swivel inflator valve and adjustable low profile exhaust valve
  • Wear-resistant knee pads provide exceptional grip and durability
  • 2mm nylon/smoothskin warm collar with vented neck drain
  • Premium reflective patches for more visibilty
  • Compression resistant socks included - for recommended Trek Boots - see below to order
  • COLOR: Black with Night Blue or Black with Electric Blue
  • MENS SIZES: Small through 3XLarge
  • Trek Boots not included - see below to order
  • FULL MANUFACTURER’S WARRANTY

BARE TREK boots sold separately click here to order

Customer Reviews for Bare D6 Pro Drysuit:

See the top 20 most helpful scuba gear reviews

Average Customer Review: based on 2 reviews.

Rating: Not a bad entry level dry suit
Reviewer: Nadine L.
This dry suit seems to do well so far. I have over 120 hours in it in the past 3 weeks. It keeps me mostly dry for the most part. Water gets in through the inflator valve which is a pain. Other then that it would of been nice to have a rubber sole on the feet to help protect the bottoms of the feet. But if your looking for a cheap dry suit, try this one, and you will be mostly satisfied.

Did this Review help?
No
Yes

117 out of 229 people found this review helpful.

Rating: Bare D6 Pro drysuit
Reviewer: Jeff L.  -  View all my reviews
My first drysuit and have only tried it in the pool, but very impressed with fit, comfort and quality. Im 62" / 210# and the XLT is a perfect fit. Hope it holds up as well as I expect it to.

Did this Review help?
No
Yes

71 out of 134 people found this review helpful.

Questions and Answers for Bare D6 Pro Drysuit:


  • Justin:

    Hello i was wondering if you customized suits if i sent u my measurements if i could get this suit customized or not?

    Bill  (Certified Scuba Instructor at Scuba.com):

    We do not do custom suits. Most divers can typically fit in stock sizes.

D6 PRO DRY - MENS

OVERVIEW

A favorite among sport and commercial divers, the D6 offers the highest warmth and protection in shallow or medium depths. This traditional neoprene offering includes a shoulder zipper that allows for less bulk and a list of standard features that will impress you. LIFETIME GUARANTEE.

STORY

At BARE we take our commitment to product quality seriously. Our drysuits in particular are legendary for their durability and longevity with many of our customers getting a full lifetime of use out of their BARE drysuit before passing it on to a friend or family member. This has allowed us to offer something that no other drysuit manufacturer has been able to do: a Lifetime Guarantee on seams and workmanship. Much more than a warranty, BARE is the fi rst and only drysuit manufacturer to offer a Lifetime Guarantee. Except for normal wear and tear, misuse or negligence, BARE will honor all claims against seams and workmanship for the life of the drysuit worldwide. Even if you’re not the original owner, you’re covered.

In a category where the next closest competitor only offers a 7-year warranty, we think you’ll agree that the BARE Guarantee says something quite extraordinary about the quality of the workmanship, materials and technology that goes into each and every one of our drysuits. We stand behind our workmanship like no one else because you deserve a product like no other.

FEATURES AND BENEFITS

Your choice of latex or a 3mm neoprene comfort-fi t neck seal
2mm nylon/smoothskin warm collar with vented neck drain provides an improved seal with the BARE dry hood
360 degree swivel inflator valve (default placement on the center of the chest)
Adjustable low-profile exhaust valve (default valve placement on upper left arm)
Your choice of neoprene or HD bottleneck latex wrist seals with talc bag
Pre-installed suspender tabs – ready to accept optional suspenders
K-PADz knee protection
Your choice of HD vulcanized 4mm compressed density neoprene BARE boot, or compression-resistant Soft Boot (see accessories for BARE boot options)
Premium badging and reflective patches
Available in custom made to measure sizes
LIFETIME GUARANTEE*

TECHNICAL SPECIFICATIONS + SIZING

Material:
6mm high-density neoprene, laminated with 'DIAMOND-TUFF' nylon
Innovation:
Newly advanced NST (No Stitch Technology) process uses the latest double heat tape technology allowing for “pin stripe” tape to be used, enhancing the suits overall stretch characteristics
TIZIP MasterSeal main entry zipper off ers improved flexibility over traditional brass zippers and uses a lower profi le design
PROTEKT shoulder, underarm and elbow protection, provide the next generation of abrasion and wear resistance and off er a high degree of stretch for comfort and freedom of movement
Entry:
Easy entry back zipper with internal protective flap
Sizing Chart
Sizes: S, MShort, M, MLTall, MLShort, ML, MTall, LShort, L, LTall, XLShort, XL, XLTall, 2XLShort, 2XL, 3XL

WATERSPORTS//SUPPORT//CONSUMER//MAINTENANCE AND CARE FAQS
DRYSUITS

BARE offers divers a series of drysuits manufactured from a wide range of materials including Neoprene, Butyl Trilaminate and Polyurethane. This range offers the diver the choice of basic suit material and construction that best meets his or her requirements.

How do I maintain the zipper on my drysuit?

Before each dive lubricate the zipper, follow the instructions on the container of zipper lubricant supplied with your suit.

Open and close the zipper a few times after the lubricant is applied to the zipper chain. The friction caused by the slider traveling over the teeth heats the lubricant causing it to flow into the teeth.

Apply a small amount of silicone grease to the sealing surface of where the slider completes the closure of the zipper. This is called the docking end of the zipper. The rubber ridges that can be seen on the inside of the docking end are where the grease should be applied. Also make sure that this area is clean and free of any other materials that may affect the seal.

Note: Always inspect the zipper for any foreign material that may affect its ability to close and create a watertight seal.

What do I need to do after the dive?

Close the zipper and rinse the outside of your drysuit with clean, fresh water. Rinse any of the inner surfaces that may have come in contact with salt water, such as the neck seal and wrist seals. Make sure that any sand, dirt, or gravel is washed away from the teeth of the zipper.

Open the zipper and hang the suit (if possible) over a piece of plastic pipe. A drysuit hanger can easily be made by passing a rope through a plastic pipe of about 3 to 4 inches in diameter and fastening both ends of the rope to an area where you can leave your suit to dry.

Note: Never leave your drysuit in direct sunlight. Ultraviolet radiation from the sun or florescent lighting will deteriorate neoprene and rubber materials (seals) very quickly. Prolonged exposure to direct sunlight will substantially lessen the life of all scuba equipment.

How should I store my drysuit?

The best way to store your drysuit is to leave it on its drying hanger in a cool, dry, dust-free area. If the suit must be stored otherwise; once it is completely dry inside and out, lay it on the floor with the zipper facing downward. Turn the boots inward and loosely rollup the legs and torso to the base of the neck seal. Bring the arms together over the top of the rolled suit so that the open zipper forms an arch as it does while you are wearing the suit. Slide the suit into its carrying bag and store it so that nothing else will be put on top of the bag.

Note: Both Neoprene and Butyl and Butyl Trilaminate materials can be damaged by exposure to petrochemical products such as gasoline/petrol, many industrial solvents, and cleaning solutions containing solvents. Avoid exposure to these chemicals during use of the drysuit and when cleaning.

Should the suit become heavily soiled, or exposed to grease, oil, etc., DO NOT CLEAN THE SUIT WITH SOLVENTS OR SOLVENT BASED CLEANERS OR DEGREASERS. You may use warm water and detergent based soaps to remove the stains. Be sure to rinse all the soap residue out with clean fresh water. Failure to follow these instruction can result in delamination and degradation of the materials.

What do I do about a leak in my drysuit?

There are many variables that must be investigated when dealing with leaks in a drysuit. Very often a leaking drysuit is not the fault of the suit itself. Usually, but not always, the cause of a leak can be determined when all of the events related to the doffing, donning, and diving with the drysuit are carefully and objectively reviewed.

For example, a diver may discover that her left foot is wet after a dive. The immediate and natural conclusion is that the suit is leaking in the left boot. The suit is checked for a leak in the left boot but no leak is found. The next time the suit is used the divers left foot stays dry. This is a very common occurrence. What often happens in this situation is that the undergarment, either a sock or an attached underwear booty is wet prior to putting it into the boot of the drysuit. During the dive the moisture eventually travels through the layers and appears as if it became wet during the dive.

The underwear boot could have become wet from being in contact with a wet piece of equipment during transport, or from stepping on wet ground prior to putting on the drysuit. Another possible cause could be water that entered the suit when it was rinsed after the last dive. Often a leak in a drysuit is clearly visible when the suit is tested, but sometimes other factors that may be determined from objective analysis are the cause.

Troubleshooting Leaks

Zipper

Problem: Wet arm, shoulder area, and crotch
Possible Cause:

Zipper not totally closed
Undergarment caught in zipper teeth
Zipper dirty (grit, lint, sand, salt, etc.)
Zipper is worn-out, damaged or broken
Other Causes:

Leaking wrist seal (water is migrating to zipper area)
Leaking neck seal
Leaking exhaust valve
Possible Solutions:

Make sure zipper is completely closed
Check undergarment for signs of being caught in the zipper
Make sure the zipper (inner teeth and outer chain) are free from debris and well lubricated
Check zipper for missing teeth, worn-through areas, or if the zipper is broken
Seals

Problem: Wet arm(s), chest and shoulder area, and crotch
Possible Cause:

Neoprene seal not tucked inward enough or at all
Undergarment disrupting the integrity of the seal
Seals may not be the correct size
Seals may be torn, split, delaminated from suit or punctured
Hair under the neck seal
May be other leak, see rest of troubleshooting
Possible Solutions:

Review instructions in the “Donning and Doffing” section of this manual
Replace the seals if they are damaged or stretched far beyond their original size, or have them altered to fit correctly
Valves

Problem: Wet arm(s), chest and shoulder area, and crotch
Possible Cause:

Valve not tightened securely to suit
Valve port delaminating from the suit
Valves are dirty or contaminated with lint from underwear
Internal diaphragm of exhaust valve damaged or displaced
May be another leak, see rest of troubleshooting
Possible Solutions:

Tighten the valve to the suit by holding the outer section and turning (clockwise) the inner section
Re-glue the valve port to the suit or return the suit for service

View all Bare Dry Suits

Choose Currency:

Scuba.com, 1752 Langley Avenue, Irvine CA 92614