- CLOSEOUT - LIMITED TO STOCK ON HAND -
Im 65" and about 190 lbs. I dive in Southern California where the water is cold. I have been troubled trying to find a wetsuit that fits me. I want something with a built in hoody. I am just wondering how this would fit. My chest is about 38", waist about 32"
Is the attached better that a separate hood? It seems like the attached would be harder to don and as long as there is a good neck seal it would be fine? Is this a good suit for Puget Sound? I have a crushed neoprene dry suit, but hate the bulk and the huge amount of weight needed as opposed to a wet/semi-dry suit.
The description says: Chest Zip gives you the freedom of zip free with the easy access of a back zip Maybe adjust that description in your listing if there is only a chest zip. Is it difficult to pull on? Ty
It is just describing the suit is as easy to put on as a back zip. It is a little different but not difficult.
I just asked the last question on this product and the info I gave was incorrect. I am 65" not 65" tall, 190lbs.
Hello Garrett, when you are sizing a wetsuit the two most important measurements are going to be your chest/bust and waist. Height is a secondary measurement and weight is the last one to take into account. Then going by the manufacture of the wet suit you are looking at and order the size of suit that you fall into.
Im just over 53" and wondering if I should get this in the "short" size. Thanks!
Hello Sandra, when you are sizing a wet suit or dive skin the two most important measurements are your chest/bust and waist. Height is a secondary measurement and weight is the last measurement you would take into account. So if your bust and waist measurements fall into the short size and your height is also in the short version size then yes the short version of that size is the one you want to go with.
It's not diving in cold water that divers dislike, it's being cold while diving. Aqua Lung is ready to assist with its new SolAfx cold water wetsuits. This across-the- chest zipper, hood-attached suit is made completely out of our four-way stretch, Aqua Flex 8mm and 7mm neoprene so you can be warm and comfortable at the same time. Say good-bye to the cold and slide into a SolAfx today.
Torso is made of 8mm, four-way stretch Aqua Flex neoprene while the legs and sleeves are made of 7mm Aqua Flex. These are the thicknesses of the base neoprene before the nylon gets added
The attached hood not only prevents cold water from entering the neck, it also features “Vent G2” technology that allows trapped regulator exhaust bubbles to exit while keeping cold water out
The “Plasmaloc” zipper has tighter tolerances and a unique integrated tooth design that make the zipper more water resistant than most competitors models
A water dam covers the neck and shoulders to add another level of thermal protection against any water ingress through the zipper
“Skin-in” gasket seals in the forearms and calves minimize water entry through the sleeves and legs
The kneepad is constructed of several independent panels that allow stretch with the Aqua Flex material
Hot, new graphics are fresh and exciting
Wetsuit Care and Maintenance
There are several different types of materials used in wetsuits to achieve specific functions. It is helpful to better understand each of these materials in order to properly care for them.
Neoprene - Neoprene is the base material that virtually all wetsuits are made of. Neoprene is a type of rubber foam and is typically laminated with other materials depending on the desired function of the material.
Standard Nylon - A standard nylon outer lining is very durable against normal wear and tear. Normal care must be taken to prevent snagging, abrasion, and cuts.
Skin material - 'skin' material may be used either inside our outside of your wetsuit and often around the wrists, ankles, and neck area. This material has a rubber like appearance either being smooth or textured, and is commonly referred to as 'skin-in' or 'skin-out'. 'Skin' neoprene material is typically used in areas where a water tight seal is desired or a benefit can be derived from it's water shedding properties. Some additional care is needed to prevent cutting, or abrasion of this material. Sharp fingernails may cut this material if care is not taken.
Thermo-skin - This material may be used inside of your wetsuit. Thermo-skin material has a silver-colored smooth skin type surface. This material has beneficial heat reflective properties and also provides a sealing surface similar to standard 'skin' materials. Some additional care is needed to prevent cutting, or abrasion of this material. Sharp fingernails may cut this material if care is not taken.
X-Flex or Iso-Flex Neoprene - X-Flex and Iso-Flex neoprene are special materials designed specifically to have a much higher rate of stretch than conventional materials. Due primarily to the looser nit needed to achieve this high degree of stretch; these materials may be more prone to snagging. Velcro may also cause some light snagging and pilling of the material. Some additional care is needed to prevent excessive abrasion or snagging.
Care before the Dive:
With any of the skin surfaces including Thermo-skin, care should be taken when donning the wetsuit to not snag the interior skin surfaces with a fingernail or toenail as this material can be cut. Avoid placing your wetsuit on or near any hot surfaces.
Care During the Dive:
The exterior surface of your wetsuit is designed to withstand the normal wear and tear you might encounter during a normal dive. Abrasion against sharp rocks or other sharp objects can cut or puncture the exterior nylon surface so reasonable care should be taken to avoid these situations. Small cuts or tears can be easily repaired with wetsuit glue. Ask your dive professional for assistance.
Care After the Dive:
When removing your wetsuit, first unzip all the zippers completely. Then remove one section at a time taking care to avoid puncturing any of skin surface panels with a fingernail.
Salt water and especially chlorine can 'dry out' the neoprene material. When neoprene material 'dries out' it looses it's flexibility. To ensure the wetsuit material retains it's flexibility for a extended period of time, it is important to thoroughly soak and rinse the wetsuit.
Soak the wetsuit in a tub of warm fresh water (not over 120°F) for at least 15-20 minutes.
After soaking, thoroughly hose off the wetsuit with fresh water
Place the suit on a thick hanger with all the zippers open to ensure maximum air circulation and complete drying.
Wetsuit material can develop a permanent crease if left folded for a extended period of time. It is best to store your wetsuit laying flat. If that is not possible, you can store your suit on a hanger. Use as thick a hanger as possible to better support the weight of the suit. The thicker the suit, the heavier, and therefore the thicker your hanger should be. There are several after-market hangers available designed specifically for this purpose.
Store in a cool, dry and protected place out of direct sunlight.
Do not store your wetsuit in garage if the garage is used to park a vehicle. The exhaust emissions from the vehicle can over time deteriorate the neoprene.
Wetsuit Zipper Care and Maintenance:
Zippers are designed to be pulled closed or open in a straight line. Try to avoid pulling on the zipper pulls at an excessive angle to their intended path of travel. It is best to ask your dive buddy for zipper assistance in either opening or closing the back-zipper of a one piece back-zipped jumpsuit.
Avoid any contact with oil, gasoline, aerosols, or chemical solvents.
Do not expose any part to aerosol spray, as some aerosol propellants attack or degrade rubber and plastic materials.
Do not use any type of alcohol, solvent or petroleum based substances to clean or lubricate any part.
Do not store your equipment near any oil, gasoline, chemicals, or solvents.
Available for shipment to U.S. zip codes only